Page:United States Statutes at Large Volume 116 Part 4.djvu/776

 116 STAT. 3204 PROCLAMATION 7529-MAR. 5, 2002 ANNEX (continued) 15 (x.w 111) tlarrollcd products designated as X-054, as described below: (A) products known as "G-type material," which are aluminum killed cold-rolled steel in coils that have increased tensile strength of 800 to 1200 N/mnv, ultra-flat, and which meet the following characteristics: thickness 0.025 mm to 0.254 mm, width 380 mm to 888 mm; chemical composition: carbon content less than 0.01 percent by weight, nitrogen content in the range 0.01 - 0.017 percent by weight, and manganese content in the range 0.6 - 0.85 percent by weight; or (B) products known as "Invar," which are certain aperture mask iron-nickel low thermal expansion Invar-type alloy products used exclusively for manufacturing shadow/aperture masks, which has an ultra-flat surface and which meets the following characteristics: thickness: 0.025 mm to 0.254 mm, width: 380 mm to 888 mm. chemical composition nickel content in the range 30.0 - 37.0 percent, by weight, cobalt content up to 5.0 percent, by weight, and sulfur content not more than 0.0030 percent, by weight; having thermal expansion coefficient not more than 1.5 x lO'^'C; (xxix) cold-rolled products known as "SPC 120," in coils, having a thickness of 1.6 mm and a width of 1040 mm, having a tensile strength of 827 MPa or more (provided for in subheading 7209.16.00), the foregoing designated as X-065; (xxx) texture rolled carbon steel flat-rolled product (TRC), not further worked than cold rolled, designated as X-205. the foregoing with a carbon content of 0.70 percent to 0.95 percent, roll-hardened to a minimum tensile strength of 1700 N/mm', with a thicknessof 0.10 mm to 1.80 mm and a width of 200 mm or less; tensile strength varies depending on the thickness of the product: 2300 - 2500 N/mm^ for thickness ranging from 0.10 mm to 0.18 mm; 2250-2470 N/mm' for thickness ranging from 0.19 mm to 0.25 mm; 1900 - 2400 N/mni- for thickness ranging from 0.26 mm to 0.79 mm; and 1750 - 2250 N/mm- for thickness ranging from 0.80 mm to 2.00 mm; meeting the specific tensile/pressure requirements or Federal Motor Vehicle Safety Standard 209; having microscopic inclusion level to DIN 50602 Rev. 9/85, section 1: SS max 3, OA, OS max 1, OG max 2; produced with OG being less than 27 microns; with chemical analysis: carbon 0.65 - 0.95 percent, silicon 0.30 percent maximum, manganese 0.55 percent maximum, phosphorus 0.02 percent maximum, sulfur 0.008 percent maximum, chromium 0.15 percent maximum and copper 0.12 percent; with a surface finish that is bright, free of roll marks, scratches, notches and cracks; longitude surface lines maximum 0.003 mm (RT - measurement method) for thickness of less than 0.66 mm and 0.005 mm for thickness over 0.60 mm.; free of complete decarburization; (xxxi) high-nickel alloy, flat-rolled product, not further worked than cold-rolled, 4.75 mm or greater in thickness, designated as X-083, containing, by weight, at least 14 percent nickel or 25 percent cobalt with or without other elements; controlled expansion alloys are composed according to specifications ASTM F15, ASTM F30, ASTM B753, and ASTM FI684; magnetic alloys composed according to specifications ASTM 8753 or ASTM A801; (xxxii) products designated as X-142, as described below: (A) non-oriented, high silicon, magnetic steel flat-rolled product, with the following characteristics: thickness 0.05 -0.20 mm; width 20-600 mm; chemical composition (by weight in percent): carbon (maximum 0.010), manganese (maximum 0.15), phosphorus (maximum 0.015), sulfur (maximum 0.005), silicon (minimum 5.0, max 7.0), aluminum (maximum 0.004); mechanical properties: hardness of 380-420 p HV (micro vickers); magnetic properties: magnetostriction (< 1.0 x lO"* (A 10/400 magnetostriction at 400 Hz, lT(=IOkG)); (B) cold-rolled carbon steet coils meeting the requirements of one or more of the products listed below (imported under subheading 7209.16.00, 7209.18.15 or 7209.18.25): (I) product 1: thickness 0.6 mm - less than 0.8 mm; minimum tensile strength 780 N/mm^; yield strength 420 - 645 N/mm^;elongation 14 percent - 25 percent; chemical composition: carbon maximum 0.10 percent by weight; silicon maximuro

�