Page:Outing-Vol 45-649-000.png



OW is the time to get ready for the ice-yachting season, and all those who want to have sport this Winter should begin now and get their boat built so that when the ice gets here they will be prepared to enjoy all of it. Take time by the forelock and build it now. The boat here described is of moderate dimensions and within the means of everybody. However, if any one wishes a larger one this plan can be enlarged to suit. This boat will be found to be the best size for the beginner and one to have the greatest pleasure with. It will take up very little storage room in summer and one person can put it together and take it apart.

All the lumber should be selected and be as free from knots as possible. The best material would be spruce or white pine. The keel, or backbone, is made of one piece, 4x6 inches, where the mast rests on it, and tapers to 4 inches square at the forward end, and 4x5 inches at the rear or stern. The next piece is the runner plank. This runs at right angles to the keel and is fastened to it in center with an iron strap that goes up each side and over top of keel, and has the ends bent out so bolts can be put through the runner plank. This strap should be bolted to the keel also. The runner plank should be to inches wide and 2 1-2 inches thick in center, and taper down to 2 inches at the outer ends. This plank is to support the runners at each end of it. Four strips of hard wood, 2x4x18 inches, should be bolted to the runner plank to form guides for the runners. There should be 1 3-4 inches between them, and they are to be bolted on and must be exactly parallel with each other so the runners will run true. If there is the least variation in them the runners will not “track” evenly and your boat will not sail very fast. This is the main point in getting a fast boat. Be very particular with the guides and runners. Now we will take up the body or cock-pit. This is made by putting a strip 1 1-2x4 inches on each side, about 3 inches from the center and on top of the runner plank, and bolting it fast. The ends run back to near the stern, and are there joined with a circle piece which is made from 1 1-2x4 inch wagon wheel rim, which can be bought at any wheelwrights or most hardware stores. The side pieces can be halved into the circle piece and bolted together. After this is done cover the bottom with tongue-and-grooved beaded boards, and your woodwork on the body of your boat is done.

The mast should be of spruce, 4 inches at the base, and taper towards the top with a swelling taper, not straight but slightly rounding as it goes towards the top. This is to give greater strength. The mast should have a foot 1 inch wide and as long as the thickness of it will permit, and be fitted with an iron strap to prevent splitting. There should be a corresponding hole cut in the top of keel timber for the mast to step into, and to prevent the keel from splitting, a strap with hole in it to fit over the one in keel timber, should be placed over it, and have two or three inches turned down on each side to fasten it to the sides of the keel. This finishes the foot of mast. The top should taper down to 2 1-2 inches and be fitted with a ring about 2 inches wide and have 4 eyes welded in on the four sides of it. These eyes are to fasten the head and side stays and the peak-halliard pulley. The boom and gaff should be made in the same manner as the mast, only that the largest place in each should be where the pulleys are fastened. The boom should be largest about four feet from the rear end, and taper both ways, so it is about 2 inches at each end, and 2 1-2 inches in largest place. The gaff should be 1 1-2 inches at each end, and 2 inches at largest place, or about 2 1-2 feet from outer end. The inner ends of both boom and gaff should be fitted with wooden jaws to straddle the mast and prevent them slipping off. The gaff jaws to have a curve upward on the inner ends, so that when the gaff is hoisted up in place the jaws will strike on both sides of the mast and not slip off as would be the case if they were straight. The jib-boom should be 1 1-2 inches at each end, and 2 inches in center, but will have no jaws, simply a straight finish.

Now we come to the sails. The best material for them will be 8-ounce duck or canvas, which can be purchased at any drygoods store. Before cutting out the sails the whole strip should have a one inch tuck run through the center and stitched down on both sides; this not only strengthens it but makes a nicer looking sail. To cut out sails the best plan would be to mark them out, full size, on the attic floor, or stake them out on the lawn, and run a string around the stakes to cut to. When cutting allow 2 1-2 inches more on all sides for the hem and lap each joint 1 inch. Always begin to cut your sails on the rear side and work towards the forward. On the lower sides of both sails cut them with a slight rocker, say about 2 inches deeper in center of main sail, and 1 1-2 inches deeper in jib. When sails are cut and stitched together, each corner should be reinforced with an extra piece of canvas, and each corner will then have a hole worked in it for the lacings. Now the lower and forward edges of the jib and the bottom, top and forward edges of the main-sail should have a strip of 3-8 inch rope sewed on them to prevent stretching, also every Io or 12 inches on