Page:HST Compton Chandra PaperModels.pdf/9



Sharp paper scissors

Razor blade knife

Dull knife

Sharp punch (such as an ice pick or nail)

Cutting surfaces (such as a wooden board)

Glue stick or rubber cement

Cellophane tape

5- by 5-centimeter-square piece of aluminum foil

Two 20-centimeter pieces of 1/8-inch dowel rods

Colored sharp point marker pens (yellow and red)

Blue and orange highlighter pens


 * Copy all model pieces on heavy weight paper.
 * Color all pieces as indicated before cutting any parts out.
 * Cut out only those pieces needed for the section being assembled at the time.
 * Use a cutting surface such as a wooden board to protect the table or desk from scratches or gouges.
 * Cut out pieces along the solid exterior lines.
 * Using the dull knife, lightly score all dashed fold lines to make accurate folds possible.
 * Apply glue to the insertion tabs on the pieces and flaps where the slots are located. If using rubber cement, apply cement to both surfaces to be joined and permit them to dry before assembling. Using a double coating of rubber cement makes a stronger bond. After the pieces are assembled. lightly rub pieces to remove excess.
 * Some pieces may require small holes to be punched through them. Those places are indicated with the (B symbol.

The seam of the cylinder should align with the word "SMALL" on the INNER RING. Reach in with a finger and press each tab to the inside wall of the cylinder. You will need to support the outer wall of the cylinder with another finger to achieve a good bond.
 * 1) Carefully cut out the following pieces: AFT SHROUD cylinder, END CAP, and INNER RING. Use the razor blade to cut small slits for the insertion of the assembly tabs of the cylinder.
 * 2) Shape the AFT SHROUD cylinder by curling the paper around the edge of a table or desk. This will permit the paper to be easily rolled into a cylinder.
 * 3) Curl the paper to form a tube. and insert the tabs of the cylinder into the slits cut in step 1. Hold the cylinder together with a piece of tape pressed to the inside.
 * 4) Fold the tabs of the INNER RING downward. Dashed lines indicate where the folds should be. Coat each tab with glue and lay the ring upside down on a flat surface. Place the cylinder over the INNER RING so that all tabs are inside.
 * 1) Fold the tabs of the END CAP downward, and coat each with glue. Place the END CAP upside down on a flat surface. and place the other end of the cylinder over it. Press the tabs in place. If you have trouble reaching the tabs. use the eraser end of a pencil in place of your finger.
 * 2) The AFT SHROUD is completed. Set it aside.


 * 1) Carefully cut out the FORWARD SHELL and LIGHT SHIELD assembly. Use the razor blade to cut the slits for the insertion of the assembly tab.
 * 2) Shape the tube by pulling the paper over the edge of a table or desk.
 * 3) Curl the paper to form a tube and insert the tabs into the slit. Use tape to hold the tube together.

RING pointed up. Insert the FORWARD SHELL and LIGHT SHIELD with the glue tab end down. Align the seam of the two cylinders.
 * 1) Bend the four glue tabs at the lower end of the FORWARD SHELL and LIGHT SHIELD inward, and cover with glue.
 * 2) Place the AFT SHROUD on a flat surface with the INNER
 * 1) Make sure the FORWARD SHELL and LIGHT SHIELD are standing straight up. Use a long piece of dowel rod to reach inside the tube. and press the tabs to the END CAP so that they will bond to the inside of the END CAP.


 * 1) Carefully cut out the OTA EOUIPMENT SECTION. Cut the slots for tab insertion with the razor blade knife.
 * 2) Curl the bay section to form a semicircle.
 * 3) Fold the tabs downward and the curved sections downward.
 * 4) 4. Apply glue to the tabs. and insert them into the slots to join the segments as indicated in the diagram.