Page:HST Compton Chandra PaperModels.pdf/16



Sharp paper scissors

Razor blade knife

Dull knife

Straight edge

Sharp punch (such as an ice pick or nail)

Glue stick or rubber cement

Cellophane tape

Cutting surface (such as a wooden board)

Silver paint or gray, yellow, and blue marker pens

Dowel rod (1/16-inch diameter)

Two Ping-Pong balls


 * Copy all model pieces on heavy weight paper.
 * Color all pieces as indicated before cutting any parts out.
 * Cut out only those pieces needed for the section being assembled at the time.
 * Use a cutting surface such as a wooden board to protect the table or desk from scratches or gouges.
 * Cut out pieces along the solid exterior lines.
 * Using the dull knife, lightly score all dashed fold lines to make accurate folds possible.
 * Apply glue to the insertion tabs on the pieces and flaps where the slots are located. If using rubber cement, apply cement to both surfaces to be joined, and permit them to dry before assembling. Using a double coating of rubber cement makes a stronger bond. After the pieces are assembled. lightly rub pieces to remove excess cement.
 * Some pieces may require small holes to be punched through them. These places are indicated with the (B symbol.


 * 1) Be sure to punch out the holes for the SOLAR ARRAY rod out of the side of the BUS (look for the two (9 symbols), and cut out the holes for the OSSE, COMPTEL, and EGRET.
 * 2) This component is easiest to assemble by joining edge A to edge B. Follow with the assembly of the other sides.
 * 3) Try to keep the joints square at all times, and smooth out any curves that might be produced.


 * 1) After forming the PROPELLANT TANKS, slip the four assembly tabs into the four slots in the bottom of the BUS. The notched end of the piece should be aligned with the OSSE end of the model. The ANTENNA rod will slide through this notch.


 * 1) Punch out the two holes indicated in the OSSE cradle. (Look for the ⊕.)
 * 2) Begin joining each cradle by inserting tabs into the corresponding slots nearest the center folds. Work your way toward the upper end of the "U" shape.
 * 3) Slide the cradles into their proper positions on the BUS. To make this easier, bend the assembly tabs upward, and gently push them into the corresponding slots. The tip of the razor blade knife can be used to assist in the insertion.
 * 4) To provide extra strength to the model, glue the surfaces of the cradles and the PROPELLANT TANKS that touch together.
 * 5) It is easiest to assemble the OSSE by folding around the curved side pieces before folding in the bottom.

ward. Fora better looking model, have the cylinder seams face each other.
 * 1) After joining each cylinder, glue and insert a Ping-Pong ball into the upper end of each. The Ping-Pong balls should form a dome at the upper end of each cylinder.
 * 2) Insert the EGRET cylinder into the model first. Use a short piece of cellophane tape to anchor it in place. Insert the tape through the COMPTEL hole. Next, insert the COMPTEL cylinder. Bend the assembly tabs on the BUS upward, and slip them into the cylinder slots as it is pushed down-


 * 1) Score the fold lines before cutting out the pieces. After making all eight BATSE pieces, glue each to the model in the places indicated in the completed model diagram.


 * 1) Be sure to punch the holes indicated in each array before cutting them out. (Look for the ⊕.)
 * 2) Coat the back side of each array with glue. and fold them together along the dashed fold lines.
 * 3) Cut one piece of dowel rod 45-centimeters long.
 * 4) Slip the rod through the holes in the BUS.
 * 5) Carefully slide one array onto each end of the rod. The rod is inserted through the holes cut open in step 6-1.