Page:EB1911 - Volume 16.djvu/864

 modern lever lock only in the fact that Barron made his gating in the bolt and carried stumps on his levers, instead of having the main stump riveted into the bolt and the gatings in the levers as is the modern practice.

A lock operating on exactly the same principle but entirely different in construction (fig. 9) was invented by Joseph Bramah in 1784. It consists of an outer barrel aaaa, within which is a revolving barrel, cccc, held in place by a steel disk, dd, and provided with a pin b fixed eccentrically for operating the bolt; the barrel is prevented from turning by sheet metal sliders ss, which slide axially in radial grooves in the barrel and project into slots cut into the steel disk which is fastened to the case of the lock. Each slider has a gating cut in its outer edge sufficiently deep to allow it to embrace the inwardly projecting steel plate and turn on it with the barrel. The key is of tubular form having slots cut in its end, each of a depth corresponding to the position of the gating in one of the sliders; so that, on inserting the key, each slider is pushed in—against a spring—exactly far enough to bring its slot opposite the steel disk; in this position the barrel carrying the sliders is turned by the key and actuates the bolt.

Up to 1851 it was generally believed that well-made lever locks of all types were practically unpickable, but at this time Alfred Charles Hobbs—an American—demonstrated, by picking the locks of Barron, Chubb, Bramah and others, that this belief was a fallacy. The method of Hobbs became widely known as the “tickling” or “tentative” method. In the modern lever lock the bolt carries a projecting piece—the “main stump”—which, when the levers are all raised to the proper height, enters the slots—“gatings”—in their faces. If, when the levers are not in this position, pressure is applied to the bolt, the main stump will press against the face of the levers; but owing to inaccuracies of workmanship and other causes the pressure will not be equal on all the levers. If now, the pressure on the bolt being maintained, each lever in turn is carefully raised a little, one will be found on which the pressure of the stump is greatest; this one is lifted till it becomes easy and then carefully lowered till it is sustained by the pressure of the stump in a new position. Another lever now bears the greatest pressure, and this in its turn is similarly treated. By this gradual or “tentative” process the levers will in time all be raised to the correct height and the bolt will slip back without, if sufficient care has been exercised, any of the levers having been raised above its correct position. Although this method of picking only became generally known in 1851, it is evident that it was not novel, since in 1817 one of Bramah’s workmen, named Russell, invented the use of false notches or gatings, which were slots similar to the true gating but of small depth cut in the face of the levers. Similar false gatings were used in Anthony Radford Strutt’s lock in 1819. The only possible object of these gatings—two of which are shown in each of the sliders of Bramah’s lock—was to prevent the tentative method of picking. They are, however, not efficient for their purpose although they render the operation more difficult and tedious.

The best-known locks up to 1851 were those of Jeremiah Chubb, their popularity being due to their superior workmanship and probably still more to their title “detector.” His lock, patented in 1818, contained a device intended to frustrate attempts at picking, and further to detect if such an attempt had been made. This device, at any rate as far as detecting was concerned, had been anticipated by the patent of Thomas Ruxton in 1816. Since the device only comes into operation when any lever is raised too high, it is not effective against a skilful application of the tentative method. The original form of this lock is shown in fig. 10, when the lever DT, which turns on a pin in the middle, is acted upon at its end T by a spring S, which will evidently allow some play to the lever on either side of the corner X; but the moment it is pushed past that point the spring will carry it farther in the same direction, like what is called in clock-work a jumper. In its proper position that end always remains above the turning-point; but, if any one of the tumblers is raised too high, the other end D of the detector, which reaches over all the levers, is lifted so far that the end T is sent down below the corner, and the tooth T then falls into a notch in the bolt, and so prevents it from being drawn back, even though all the levers are raised properly by the right key. It thus at once becomes obvious that somebody has been trying to pick the lock. The way to open it, then, is to turn the key the other way, as if to overlock the bolt; a short piece of gating near the end of the levers allows the bolt to advance just far enough to push the tooth of the detector up again by means of its inclination there, and then the lock can be opened as usual. To render the mechanism of locks more inaccessible for picking purposes, two devices, the “curtain” and the “barrel,” were in use; these devices were simply the one a disk and the other a cylinder carrying a keyhole which revolved with the key and so closed the fixed keyhole in the case.

It is to Hobbs himself that we are indebted for the invention of the movable stump, since called the safety lever, the only device introduced rendering the tentative method of picking inoperative. This invention was incorporated in the “protector” locks of Hobbs, Hart & Co.; it consists in the employment of a movable main stump which is not riveted into the bolt as usual, but is set on the end b of a bent lever abc (fig. 11) which lies in a hollow of the bolt A behind it, turning on a pivot in the bolt itself, and kept steady by a small friction-spring e. The stump comes through a hole in the bolt large enough to let it have a little play; and the long end a of the lever stands just above the edge of a square pin d, which is fixed in the back plate of the lock. When the lock is locked, if the bolt be pushed