Page:EB1911 - Volume 15.djvu/906

Rh Figure-of-Eight Knot (fig. 2).—Used only to prevent ropes from unreeving; it forms a large knob.

Reef Knot (figs. 3, 4).—Form an overhand knot as above. Then take the end a over the end b and through the bight. If the end a were taken under the end b, a granny would be formed. This knot is so named from being used in tying the reef-points of a sail.

Bowline (figs. 5–7).—Lay the end a of a rope over the standing part b. Form with b a bight c over a. Take a round behind b and down through the bight c. This is a most useful knot employed to form a loop which will not slip. Running bowlines are formed by making a bowline round its own standing part above b. It is the most common and convenient temporary running noose.

Bowline on a Bight (figs. 8, 9).—The first part is made similar to the above with the double part of the rope; then the bight a is pulled through sufficiently to allow it to be bent over past d and come up in the position shown in fig. 9. It makes a more comfortable sling for a man than a single bight.

Half-Hitch (fig. 10).—Pass the end a of the rope round the standing part b and through the bight.

Two Half-Hitches (fig. 11).—The half-hitch repeated; this is commonly used, and is capable of resisting to the full strength of the rope. A stop from a to the standing part will prevent it jamming.

Clove Hitch (figs. 12, 13).—Pass the end a round a spar and cross it over b. Pass it round the spar again and put the end a through the second bight.

Blackwall Hitch (fig. 14).—Form a bight at the end of a rope, and put the hook of a tackle through the bight so that the end of the rope may be jammed between the standing part and the back of the hook.

Double Blackwall Hitch (fig. 15).—Pass the end a twice round the hook and under the standing part b at the last cross.

Cat’s-paw (fig. 16).—Twist up two parts of a lanyard in opposite directions and hook the tackle in the eyes i, i. A piece of wood should be placed between the parts at g. A large lanyard should be clove-hitched round a large toggle and a strap passed round it below the toggle.

Marling-spike Hitch (fig. 17).—Lay the end a over c; fold the loop over on the standing part b; then pass the marline-spike through, over both parts of the bight and under the part b. Used for tightening each turn of a seizing.

Fisherman’s Bend (fig. 18).—Take two turns round a spar, then a half-hitch round the standing part and between the spar and the turns, lastly a half-hitch round the standing part.

Studding-sail Halyard Bend (fig. 19).—Similar to the above, except that the end is tucked under the first round turn; this is more snug. A magnus hitch has two round turns and one on the other side of the standing part with the end through the bight.

Timber Hitch (fig. 20).—Take the end a of a rope round a spar, then round the standing part b, then several times round its own part c, against the lay of the rope.

Carrick Bend (fig. 21).—Lay the end of one hawser over its own part to form a bight as e′, b; pass the end of another hawser up through that bight near b, going out over the first end at c, crossing under the first long part and over its end at d, then under both long parts, forming the loops, and above the first short part at b, terminating at the end e″, in the opposite direction vertically and horizontally to the other end. The ends should be securely stopped to their respective standing parts, and also a stop put on the becket or extreme end to prevent it catching a pipe or chock; in that form this is the best quick means of uniting two large hawsers, since they cannot jam. When large hawsers have to work through small pipes, good security may be obtained either by passing ten or twelve taut racking turns with a suitable strand and securing each end to a standing part of the hawser, or by taking half as many round turns taut, crossing the ends between the hawsers over the seizing and reef-knotting the ends. This should be repeated in three places and the extreme ends well stopped. Connecting hawsers by bowline knots is very objectionable, as the bend is large and the knots jam.

Sheet Bend (fig. 22).—Pass the end of one rope through the bight of another, round both parts of the other, and under its own standing part. Used for bending small sheets to the clews of sails, which present bights ready for the hitch. An ordinary net is composed of a series of sheet bends. A weaver’s knot is made like a sheet bend.

Single Wall Knot (fig. 23).—Unlay the end of a rope, and with the strand a form a bight. Take the next strand b round the end of a.