Page:EB1911 - Volume 06.djvu/829

Rh Fig. 4 shows the general arrangement of mounting all compass cards in the bowl. In fig. 5 another form of compass called a liquid or spirit compass is shown partly in section. The card nearly floats in a bowl filled with distilled water, to which 35% of alcohol is added to prevent freezing; the bowl is hermetically sealed with pure india-rubber, and a corrugated expansion chamber is attached to the bottom to allow for the expansion and contraction of the liquid. The card is a mica disk, either painted as in fig. 1, or covered with linen upon which the degrees and points are printed, the needles being enclosed in brass.

Great steadiness of card under severe shocks and vibrations, combined with a minimum of friction in the cap and pivot, is obtained with this compass. All compasses are fitted with a gimbal ring to keep the bowl and card level under every circumstance of a ship’s motion in a seaway, the ring being connected with the binnacle or pedestal by means of journals or knife edges. On the inside of every compass bowl a vertical black line is drawn, called the “lubber’s point,” and it is imperative that when the compass is placed in the binnacle the line joining the pivot and the lubber’s point be parallel to the keel of the vessel. Thus, when a degree on the card is observed opposite the lubber’s point, the angle between the direction in which the ship is steering and the north point of the compass or course is at once seen; and if the magnetic variation and the disturbing effects of the ship’s iron are known, the desired angle between the ship’s course and the geographical meridian can be computed. In every ship a position is selected for the navigating or standard compass as free from neighbouring iron as possible, and by this compass all courses are shaped and bearings taken. It is also provided with an azimuth circle or mirror and a shadow pin or style placed in the centre of the glass cover, by either of which the variable angle between the compass north and true north, called the “total error,” or variation and deviation combined, can be observed. The binnacles or pedestals for compasses are generally constructed of wood about 45 in. high, and fitted to receive and alter at pleasure the several magnet and soft iron correctors. They are also fitted with different forms of suspension in which the compass is mounted to obviate the mechanical disturbance of the card caused by the vibration of the hull in ships driven by powerful engines.

The effects of the iron and steel used in the construction of ships upon the compass occupied the attention of the ablest physicists of the 19th century, with results which enable navigators to conduct their ships with perfect safety. The hull of an iron or steel ship is a magnet, and the distribution of its magnetism depends upon the direction of the ship’s head when building, this result being produced by induction from the earth’s magnetism, developed and impressed by the hammering of the plates and frames during the process of building. The disturbance of the compass by the magnetism of the hull is generally modified, sometimes favourably, more often unfavourably, by the magnetized fittings of the ship, such as masts, conning towers, deck houses, engines and boilers. Thus in every ship the compass needle is more or less subject to deviation differing in amount and direction for every azimuth of the ship’s head. This was first demonstrated by Commander Matthew Flinders by experiments made in H.M.S. “Investigator” in 1800–1803, and in 1810 led that officer to introduce the practice of placing the ship’s head on each point of the compass, and noting the amount of deviation whether to the east or west of the magnetic north, a process which is in full exercise at the present day, and is called “swinging ship.” When speaking of the magnetic properties of iron it is usual to adopt the terms “soft” and “hard.” Soft iron is iron which becomes instantly magnetized by induction when exposed to any magnetic force, but has no power of retaining its magnetism. Hard iron is less susceptible of being magnetized, but when once magnetized it retains its magnetism permanently. The term “iron” used in these pages includes the “steel” now commonly employed in shipbuilding. If an iron ship be swung when upright for deviation, and the mean horizontal and vertical magnetic forces at the compass positions be also observed in different parts of the world, mathematical analysis shows that the deviations are caused partly by the permanent magnetism of hard iron, partly by the transient induced magnetism of soft iron both horizontal and vertical, and in a lesser degree by iron which is neither magnetically hard nor soft, but which becomes magnetized in the same manner as hard iron, though it gradually loses its magnetism on change of conditions, as, for example, in the case of a ship, repaired and hammered in dock, steaming in an opposite direction at sea. This latter cause of deviation is called sub-permanent magnetism. The horizontal directive force on the needle on board is nearly always less than on land, sometimes much less, whilst in armour-plated ships it ranges from .8 to .2 when the directive force on land = 1.0. If the ship be inclined to starboard or to port additional deviation will be observed, reaching a maximum on north and south points, decreasing to zero on the east and west points. Each ship has its own magnetic character, but there are certain conditions which are common to vessels of the same type.

Instead of observing the deviation solely for the purposes of correcting the indications of the compass when disturbed by the iron of the ship, the practice is to subject all deviations to mathematical analysis with a view to their mechanical correction. The whole of the deviations when the ship is upright may be expressed nearly by five co-efficients, A, B, C, D, E. Of these A is a deviation constant in amount for every direction of the ship’s head. B has reference to horizontal forces acting in a longitudinal direction in the ship, and caused partly by the permanent magnetism of hard iron, partly by vertical induction in vertical soft iron either before or abaft the compass. C has reference to forces acting in a transverse direction, and caused by hard iron. D is due to transient induction in horizontal soft iron, the direction of which passes continuously under or over the compass. E is due to transient induction in horizontal soft iron unsymmetrically placed with regard to the compass. When data of this character have been obtained the compass deviations may be mechanically corrected to within 1°—always adhering to the principal that “like cures like.” Thus the part of B caused by the permanent magnetism of hard iron must be corrected by permanent magnets horizontally placed in a fore and aft direction; the other part caused by vertical soft iron by means of bars of vertical soft iron, called Flinders bars, before or abaft the compass. C is compensated by permanent magnets athwart-ships and horizontal; D by masses of soft iron on both sides of the compass, and generally in the form of cast-iron spheres, with their centres in the same horizontal plane as the needles; E is usually too small to require correction; A is fortunately rarely of any value, as it cannot be corrected. The deviation observed when the ship inclines to either side is due—(1) to hard iron acting vertically upwards or downwards; (2) to vertical soft iron immediately below the compass; (3) to vertical induction in horizontal soft iron when inclined. To compensate (1)