Page:EB1911 - Volume 04.djvu/1003

 which are hinged together at Q. At O is a needle-point which is driven into the drawing-board, and at T is the tracer. As this is guided round the boundary of the figure a wheel W mounted on QT rolls on the paper, and the turning of this wheel measures, to some known scale, the area. We shall give the theory of this instrument fully in an elementary manner by aid of geometry. The theory of other planimeters can then be easily understood.

Consider the rod QT with the wheel W, without the arm OQ. Let it be placed with the wheel on the paper, and now moved perpendicular to itself from AC to BD (fig. 6). The rod sweeps over, or generates, the area of the rectangle ACDB = lp, where l denotes the length of the rod and p the distance AB through which it has been moved. This distance, as measured by the rolling of the wheel, which acts as a curvometer, will be called the “roll” of the wheel and be denoted by w. In this case p = w, and the area P is given by P = wl. Let the circumference of the wheel be divided into say a hundred equal parts u; then w registers the number of u’s rolled over, and w therefore gives the number of areas lu contained in the rectangle. By suitably selecting the radius of the wheel and the length l, this area lu may be any convenient unit, say a square inch or square centimetre. By changing l the unit will be changed.

Again, suppose the rod to turn (fig. 7) about the end Q, then it will describe an arc of a circle, and the rod will generate an area l&#8202;2, where is the angle AQB through which the rod has turned. The wheel will roll over an arc c, where c is the distance of the wheel from Q. The “roll” is now w = c; hence the area generated is

P = $l&#8202;^{2}⁄c$ w,

and is again determined by w.

Next let the rod be moved parallel to itself, but in a direction not perpendicular to itself (fig. 8). The wheel will now not simply roll. Consider a small motion of the rod from QT to Q′T′. This may be resolved into the motion to RR′ perpendicular to the rod, whereby the rectangle QTR′R is generated, and the sliding of the rod along itself from RR′ to Q′T′. During this second step no area will be generated. During the first step the roll of the wheel will be QR, whilst during the second step there will be no roll at all. The roll of the wheel will therefore measure the area of the rectangle which equals the parallelogram QTT′Q′. If the whole motion of the rod be considered as made up of a very great number of small steps, each resolved as stated, it will be seen that the roll again measures the area generated. But it has to be noticed that now the wheel does not only roll, but also slips, over the paper. This, as will be pointed out later, may introduce an error in the reading.

We can now investigate the most general motion of the rod. We again resolve the motion into a number of small steps. Let (fig. 9) AB be one position, CD the next after a step so small that the arcs AC and BD over which the ends have passed may be considered as straight lines. The area generated is ABDC. This motion we resolve into a step from AB to CB′, parallel to AB and a turning about C from CB′ to CD, steps such as have been investigated. During the first, the “roll” will be p the altitude of the parallelogram; during the second will be c. Therefore

The area generated is lp + l2, or, expressing p in terms of w, lw + (l2 - lc). For a finite motion we get the area equal to the sum of the areas generated during the different steps. But the wheel will continue rolling, and give the whole roll as the sum of the rolls for the successive steps. Let then w denote the whole roll (in fig. 10), and let denote the sum of all the small turnings ; then the area is

Here is the angle which the last position of the rod makes with the first. In all applications of the planimeter the rod is brought back to its original position. Then the angle is either zero, or it is 2 if the rod has been once turned quite round.

Hence in the first case we have

and w gives the area as in case of a rectangle.

In the other case

where C = (l−c)2, if the rod has once turned round. The number C will be seen to be always the same, as it depends only on the dimensions of the instrument. Hence now again the area is determined by w if C is known.

Thus it is seen that the area generated by the motion of the rod can be measured by the roll of the wheel; it remains to show how any given area can be generated by the rod. Let the rod move in any manner but return to its original position. Q and T then describe closed curves. Such motion may be called cyclical. Here the theorem holds:—If a rod QT performs a cyclical motion, then the area generated equals the difference of the areas enclosed by the paths of T and Q respectively. The truth of this proposition will be seen from a figure. In fig. 11 different positions of the moving rod QT have been marked, and its motion can be easily followed. It will be seen that every part of the area TT′BB′ will be passed over once and always by a forward motion of the rod, whereby the wheel will increase its roll. The area AA′QQ′ will also be swept over once, but with a backward roll; it must therefore be counted as negative. The area between the curves is passed over twice, once with a forward and once with a backward roll; it therefore counts once positive and once negative; hence not at all. In more complicated figures it may happen that the area within one of the curves, say TT′BB′, is passed over several times, but then it will be passed over once more in the forward direction than in the backward one, and thus the theorem will still hold.

12.

To use Amsler’s planimeter, place the pole O on the paper outside the figure to be measured. Then the area generated by QT is that of the figure, because the point Q moves on an arc of a circle to and fro enclosing no area. At the same time the rod comes back without making a complete rotation. We have therefore in formula (1), = 0; and hence